has a history of over four decades of business activities. Teyseer Industrial Supplies & Services Company W.L.L. (TISSCO), member of Teyseer Group, established in the year 1999 as an industrial supplies and services company. TISSCO, an ISO 9001:2008 certified, is focused on supplies and services of Electro Mechanical Industrial Products, in Qatar.
Hot Products : Welling Air Conditioner Motor, Fan Motor 93473312 Screw Air Compressor Parts, Elk Brand China 0.75kw 6p Crane Motor with Buffer, 50/67 Frame Cross-Belt Sorter BLDC Roller, High Quality Die Casting Sand Cast Water Pump Electric Motor, Electric DC Robot Motor 48V High Power Brushless Motor Drum Conveyor Roller
Pressure Temperature Chart 800.497.6805 www.icorinternational.com “making your life easier” COIL TEMPERATURE CHART INSTRUCTIONS Select design temperature for your evaporator and condenser-Match to approx. operational pressures. NU-22 - 120° condensing / 40° evaporator approx. 234 psig head / 60 psig suction
(A) Cooling 80°F DB, 67°F WB air entering indoor coil, 95°F DB air entering outdoor coil. (B) High Temperature Heating 47°F DB, 43°F WB air entering outdoor coil, 70°F DB air entering indoor coil. (C) Low Temperature Heating 17°Fly mount condensing unit to a frame or pad without removing DB, 15°F WB air entering
Coil Transfer Cars made in the USA. Standard and custom lift models are available. Get in touch with a lift expert. Call Now: 1-888-711-5438
80 100 50 60 70 80 90 100 Outside Air Temperature [F] d Stage 2 Stage 1 The optimizing controller tuned the RTU’s operation according to varying conditions as expected. Shown is control of damper position and condenser fan speed with change in humidity and temperature.
The example chilled-water coil in Figure 1 is in a mixed-air VAV air handler that cools 7000 cfm to 53°F leaving the coil. The entering chilled-water temperature is 42 °F, with a 15°F ΔT at design conditions. Table 1 compares four coils that could be used for this application: † Coil #1 has six rows of 3/8-inch
Single refrigerant loop scroll compressors range from 2 to 25 tons with the largest capable of 80 tons. Typical chilled water cooling temperature ranges between 39-45 °F. For proper heat transfer between the circulated water to be cooled and the refrigerant, it is important to maintain sufficient chiller water flow.
May 14, 2014 · Divide 286,000 (amount of energy to melt a ton of ice), by 24 (hours in a day), the result is 11,917 BTU’s of energy per hour to melt the ton of ice. The industry rounded up to 12,000 Btu/h to reference 1-ton of air conditioner capacity. Therefore, a 2-ton A/C unit will remove 24,000 BTU’s of heat per hour; a 3-ton A/C unit will remove
Oct 01, 1999 · Although both coils will fit,we selected the 13.7-sq-ft coil which offers the best combination of performance and economy. The coil would be installed along the 10-ft wall of the tank. If the installation had to be along the 3-ft wall, a coil with 13.7 sq ft of surface area and dimensions of 36.5 wide by 24 inches long (Table V) could be used.
1. 1 Ton = 2,000 lbs. 2. Minimum sling length when using standard eyes. Note: Length Tolerances - Single Part Wire Rope Slings - Standard length tolerance is plus or minus two rope diameters, or plus or minus 0.5% of the sling length, whichever is greater. ** See page 91 for reduced choker capacity when using these hook sizes. * WARNING
Jun 20, 2021 · Even the product name on the box is “Multi-coil wireless fast charging board”. It’s a pretty complex design and the PCB inspection is thorough enough to give you an idea of its capabilities
For older ignition coils that have cracks, silicone dielectric grease can also be applied to the shaft of the coil to prevent spark jump, but the permanent way to repair spark jump is to replace the boot or the entire coil. For ignition coils and coil packs that connect to spark plug wires, silicone dielectric grease is use the same way.
Master Bond features an extensive line of heat resistant adhesives, sealants, coatings and potting/encapsulation compounds that can withstand temperatures as severe as 600°F and higher. These materials were designed to resist short term and long term exposure to elevated temperatures while maintaining their mechanical and electrical properties.
Nov 16, 2017 · Chillers provide a continuous flow of coolant to the cold side of a process water system at a desired temperature of about 50°F (10°C). The coolant is then pumped through the process, extracting heat out of one area of a facility (e.g., machinery, process equipment, etc.) as it flows back to the return side of the process water system. A